Access Point Firmware Releases

• This firmware update supports the Dynamic VLANs and Captive Portal Enhancements beta features.
• You can now reboot the access point from the access point local Web UI. This is available in the top-right corner of the Web UI when you click on the user account icon.
• The Live Status > Clients monitoring page in WatchGuard Cloud now loads client data much faster. [AP-1792, WIFI-8250]

This update also includes these resolved issues:

• An SNMP licensing issue is resolved. [AP-1692]
• DCS now operates correctly to set an optimal channel from the candidate channels list. [AP-1703]
• The access point transmit power is now correctly set to the values from the device configuration after a firmware upgrade. [AP-1756]
• The country of operation for the access point is now correctly updated when a device with no SSIDs configured is connected in a new region. [AP-1757]
• The access point connection status in WatchGuard Cloud now shows the correct status and is consistent with the local Web UI. [AP-1774]
• An access point with an expired MSSP license is now correctly disconnected and deregistered from WatchGuard Cloud. [AP-1801]

• With this firmware update, the access point now uses a cryptographic signature to verify the integrity of the device each time the access point boots. Integrity checks make sure that system files are valid and have not been corrupted. For more information, go to Access Point System Integrity Checks.
• This firmware update also supports the Network Access Enforcement and Enterprise Authentication Enhancements features.

You must currently run firmware version v2.0.28 or higher to upgrade to v2.1.12. If your access point runs a firmware version lower than v2.0.28 and you upgrade directly to v2.1.12, the device will upgrade twice, first to v2.0.28 and then to v2.1.12 automatically. It might take additional time for the firmware upgrade to complete.

This update also includes these enhancements and resolved issues:

• In some cases, access points managed by WatchGuard Cloud were incorrectly reported as threat access points. [AP-1617]
• Fast Roaming for wireless clients now works correctly with WPA2 Enterprise security. [WIFI-8251]
• Traffic shaping now consistently limits upload and download traffic as configured. [AP-1689]
• NTP server retry attempts are no longer delayed in some scenarios. [AP-1668]
• The diagnostic snapshot file download no longer times out when multiple wireless clients are connected. [AP-1659]
• The AP432 now uses the correct transmit power when it is configured to use the minimum setting of 8 dBm. [AP-1704]
• The diagnostic snapshot file now contains additional information for troubleshooting.

• With this firmware update, the access point now uses a cryptographic signature to verify the integrity of the device each time the access point boots. Integrity checks make sure that system files are valid and have not been corrupted.

• This firmware update also supports the Network Access Enforcement and Enterprise Authentication Enhancements beta features.

This update also includes these enhancements and resolved issues:

• Fast Roaming for wireless clients now works correctly with WPA2 Enterprise security. [WIFI-8251]
• Traffic shaping now consistently limits upload and download traffic as configured. [AP-1689]
• NTP server retry attempts are no longer delayed in some scenarios. [AP-1668]
• The diagnostic snapshot file download no longer times out when multiple wireless clients are connected. [AP-1659]
• The AP432 now uses the correct transmit power when it is configured to use the minimum setting of 8 dBm. [AP-1704]
• The diagnostic snapshot file now contains additional information for troubleshooting.

This is an important security update that enables a cryptographic signature to verify the integrity of future signed firmware files before each software upgrade. Integrity checks make sure that system files are valid and have not been corrupted. After you upgrade to an access point firmware version that includes integrity checks, you cannot downgrade to a version that is not signed by WatchGuard. This access point firmware version 2.0.28 becomes the minimum version required before you can install any future firmware upgrades.

This update also provides these enhancements and resolved issues:

• You can now configure up to 3 NTP servers in a device configuration or an Access Point Site. [AP-1527]
• You can now configure the Device LEDs option in an Access Point Site. [WIFI-8105]
• The access point diagnostic snapshot file now includes the system information, associated wireless clients, and rogue access point wired and wireless network scan results. [AP-1324, AP-1511, AP-1524].
• The Realtime traffic status in the local access point Web UI no longer shows negative values. [AP-1410]
• The Device status in the local access point Web UI now correctly shows the channel for the 5 GHz radio. [AP-1537]
• Font display inconsistencies in the access point local Web UI are resolved. [AP-1538, AP1539]
• An access point configuration can now be correctly deployed when the 2.4 GHz channel width is set to 20/40MHz in the European region. [AP-1566]
• Access point transmit power settings are now correctly applied to prevent exceeding the maximum power for a region. [WIFI-7961]

This firmware update enables support for the Airspace Monitoring feature, a new access point local Web UI, and resolves these issues:

• The RADIUS accounting interim update and stop packets now include the correct traffic size for the client. [AP-1353]
• The access point CLI tpmtest command now executes correctly. [AP-1390]
• This release includes Airspace Monitoring optimizations since the last beta version.
• This release includes minor access point Web UI page and text updates since the last beta version.

This firmware update enables support for the Airspace Monitoring beta feature, a new access point local Web UI, and resolves these issues:

• The RADIUS accounting interim update and stop packets now include the correct traffic size for the client. [AP-1353]
• The access point CLI tpmtest command now executes correctly. [AP-1390]

Resolved Issues

• The RADIUS accounting server shared secret is now correctly processed by the access point to allow the server and access point to exchange accounting messages. [AP-1351]
• NTP server connection alerts are optimized to reduce the number of connection alerts. [AP-1358]
• This release updates the version of OpenSSH to 9.0p1. [AP-1307]
• The SSL/TLS cipher key size for DH/RSA exchange is increased to 2048 bits. [AP1341]
• New commands are available in the access point CLI to show and test the RSA public key of the access point for troubleshooting connections to WatchGuard Cloud.

New Features and Enhancements

• This update is required for the access point SNMP monitoring feature.
• You can now add up to 256 MAC addresses for the MAC Address Access Control feature.

Resolved Issues

• After the installation of access point firmware 1.1.23, the AP130 fails to broadcast an SSID with NAT enabled on the 2.4 GHz radio. [AP-1320]

This update replaces the current 1.1.22 beta firmware, and resolves these issues:

• SSIDs failed to broadcast after the installation of firmware version 1.1.22 on the AP130. [AP-1311]
• Radar detection traps are not sent to the trap server. [AP-1295]

This update is required for the SNMP monitoring beta feature.

New Features and Enhancements

This update adds support for the access point Description and Radio Details features.

Resolved Issues

• Wireless clients now successfully reconnect to an access point with WPA2 and WPA3 Enterprise authentication. [AP-1163]
• Wireless clients now correctly obtain an IP address after you change the access point from a static IP address with a management VLAN enabled to a DHCP only address. [AP-1222]
• Security scan warnings no longer occur for the access point certificate and hashing algorithm for local access to the device. [AP-1165]
• Syslog entries accessed from the access point CLI interface are now correctly displayed in time-sequential order with the newest entries at the end of the list. [AP-1061]

Enhancements

• This update is required to use the Diagnostic Tools and Support Snapshot features.
• The access point LED indicator status is enhanced to provide more granular status of the device connection to WatchGuard Cloud. This enables you to more accurately troubleshoot the issue if the access point status stops in a specific state. For more information about the LED status and how to troubleshoot connection issues, see the Hardware Guide for your device.

Resolved Issues

• The correct wireless mode for a client now appears on the Live Status > Clients monitoring page. [AP-1140]
• The operating system of Apple iOS 14.8 and 15.x wireless clients are now correctly identified. [AP-1075]
• You can now correctly disable a VLAN on an SSID after you enable the Captive Portal feature. [AP-1092]
• Dynamic channel selection now correctly switches to a new channel when interference is detected on the current channel. [AP-1115]
• Access point firmware upgrade from the CLI now correctly validates the specified download link and correct firmware version for the device model. [AP-1039, AP-1083]

• This update is required to use the Diagnostic Tools and Support Snapshot beta features. To learn more or to report an issue, go to the Wi-Fi in WatchGuard Cloud Beta test community.
• The operating system of Apple iOS 14.8 and 15.x wireless clients are now correctly identified. [AP-1075]
• You can now correctly disable a VLAN on an SSID after you enable the Captive Portal feature. [AP-1092]
• Dynamic channel selection now correctly switches to a new channel when interference is detected on the current channel. [AP-1115]
• Access point firmware upgrade from the CLI now correctly validates the specified download link and correct firmware version for the device model. [AP-1039, AP-1083]

• This update is required to use the Diagnostic Tools and Support Snapshot beta features. To learn more or to report an issue, go to the Wi-Fi in WatchGuard Cloud Beta test community.

• Access Point VPN now correctly connects when the Firebox VPN settings use a domain name of 16 characters or greater. [AP-1105]
• Minor bug fixes and enhancements. [AP-1077, AP-1085, AP-1086]

• Initial firmware release.