Monitor Neighbor Wi-Fi

Applies To: WatchGuard Cloud-managed Access Points (AP130, AP230W, AP330, AP332CR, AP340, AP430CR, AP432)

You can view neighboring Wi-Fi networks detected by your access points in WatchGuard Cloud. The Neighbor Wi-Fi page shows a signal strength chart by channel and a list of detected neighbor BSSIDs so you can identify nearby wireless networks that might cause interference.

It might take several minutes for the Neighbor Wi-Fi chart to initially show data.

Neighbor Wi-Fi requires:

  • A WatchGuard USP Wi-Fi Management license
  • Access point firmware v3.4 or higher

To monitor neighbor Wi-Fi networks:

  1. Select Monitor > Devices.
  2. Select an access point or a folder that contains your access points.
  3. Select Live Status > Neighbor Wi-Fi.
    The Neighbor Wi-Fi page opens.

Screen shot of the Live Status > Neighbor Wi-Fi monitor page in WatchGuard Cloud

The chart uses different colors so that networks on adjacent channels are easy to tell apart. The colors do not indicate signal strength, channel utilization, security status, or any other network characteristic.

  • To view neighbor Wi-Fi data for a specific frequency band, select the 2.4 GHz, 5 GHz, or 6 GHz tab. Wi-Fi 6 access points show the 2.4 GHz and 5 GHz bands. The 6 GHz band requires a Wi-Fi 7 access point.
  • The page refreshes the data every 4 minutes. To pause auto-refresh for the displayed data, click . To restart auto-refresh, click .
  • To search the neighbor Wi-Fi list, type a search query in the Search text box.
  • To filter the neighbor Wi-Fi list by channel, signal strength, security type, or wireless mode, click .
  • To select which columns appear in the table, click .
  • To export the neighbor Wi-Fi list as a CSV file, click .

The chart shows neighbor wireless networks detected on each channel in the selected frequency band. Each SSID appears once in the chart, at the strongest signal currently detected by any access point. In the table below, the Detected By and Signal Strength columns show each access point that detected the network and the signal strength it reported.

  • The vertical axis shows signal strength in dBm, from 0 to −90. Values closer to 0 indicate a stronger signal.
  • The horizontal axis shows the channels available in that band.
  • The width of each line represents the network's channel width.
  • To view the channel number, the number of SSIDs detected on that channel, hover over a channel in the chart.
  • Each access point excludes its own broadcast SSIDs from the neighbor Wi-Fi data.

If no neighbor networks are available, the page shows No Neighbor Wi-Fi Networks. This can occur when there are no nearby networks in the airspace, the access point is offline, the access point firmware is lower than v3.4, the access point does not have a valid USP Wi-Fi Management license, or scanning is paused for threat remediation. Note that it might take several minutes for the Neighbor Wi-Fi chart to initially show data after the initial scan. For more information, go to Neighbor Wi-Fi report shows No Neighbor Wi-Fi Networks.

The Neighbor Wi-Fi page includes this data:

  • BSSID — The MAC address of the neighboring access point radio.
  • SSID Name — The name of the neighboring wireless network. Hidden networks show as <Hidden SSID>.
  • Channel — The wireless channel in use by the neighboring access point.
  • Channel Width — The channel width in use by the neighboring access point, such as 20 MHz.
  • Neighbor AP — The name of the neighboring access point if WatchGuard Cloud identifies it as a WatchGuard access point or another vendor. Unidentified neighbors are nearby wireless networks not managed by WatchGuard Cloud, and identification is based on observed radio data.
  • Detected By — The managed access point that detected the neighboring network. In a folder or account view, this can show more than one detecting access point.
  • Signal Strength (dBm) — The measured signal strength of the neighboring network relative to the detecting access point. Signal strength is represented in -dBm format (-100 to 0). The closer the value is to 0 dBm, the stronger the signal. For example, -40 dBm is better signal strength than -60 dBm. By default, the table sorts by signal strength from strongest to weakest.
  • Number of Clients — The number of wireless clients currently connected to the neighboring access point.

    The client count might not always be exact. Access points without a dedicated scanning radio might show 0 clients for neighboring networks.

  • Security — The security mode of the neighboring wireless network, such as Open, WPA2 Personal, or WPA3 Enterprise.
  • Wireless Mode — The wireless mode in use by the neighboring access point, such as 802.11ax or 802.11be.
  • Max Data Rate — The maximum data rate of the neighboring access point.

Related Topics

Monitor Access Point Radios

Monitor Access Point SSIDs

View Wireless Clients

Access Point Airspace Monitoring Report

Monitor Access Points